Skip to content
LawnElm

Money

Measuring your yard: square feet, linear feet and acres

Every yard quote and every bag of seed starts from a measurement. Two units cover most of it, square feet for areas and linear feet for runs.

By LawnElm Editorial Team Updated 6 min read

One acre
43,560 sq ft
Rates are per
1,000 sq ft
Fences and edging
Linear feet
Lawn area
Lot minus non-turf
Illustration: a yard plan with a tape measure, a rectangle, a triangle and a long fence line

Short version

Lawn area is the lot minus everything that is not grass: house, drive, walks, patio and beds. One acre is 43,560 square feet, and fertilizer and seed rates are usually written per 1,000 square feet. Fences, edging and gutters are measured in linear feet along the run. The lot to lawn tool does the subtraction. It does not know slope, shade, fences or gates, so use its number to compare quotes and not as a measurement for a contract.

Start with the lot and subtract

The lot to lawn tool takes the lot size in square feet or acres, then the footprints to remove: the house and garage, the driveway, walks and patio, and beds, trees and anything else such as a shed, a pool or a play set. It subtracts them and shows the lawn in square feet, in acres, as a share of the lot and in units of 1,000 square feet. If the footprints add up to more than the lot, it asks you to check the numbers.

The lot size is on your county assessor's parcel record, usually free to search by address, and on a property survey or closing papers. The tool then links on to the yard budget and the lawn supplies tools with your lawn area already filled in.

Units you will see on quotes and labels
UnitWhat it meansWhere it is used
Square foot1 foot by 1 footLawn jobs, sod, seed
1,000 square feetThe unit rates are written inFertilizer and seed labels
Acre43,560 square feetLot sizes
Linear foot1 foot of length, any widthFences, edging, gutters

Measure the shapes

A tape or a measuring wheel is the most accurate method, according to the University of Minnesota's turfgrass program. Divide an irregular lawn into simple shapes, measure each and add the results. The Rutgers fertilizer fact sheet gives the formulas: for a rectangle or square, multiply length by width in feet; for a triangle, multiply base by height and divide by two. Both sources add up the sections to get the total.

Shape formulas (Rutgers Cooperative Extension)
ShapeFormulaExample
Rectangle or squareLength × width40 ft × 25 ft = 1,000 sq ft
TriangleBase × height ÷ 230 ft × 20 ft ÷ 2 = 300 sq ft
Irregular lawnSplit into sections, add the areasAdd each section

Rutgers says the total should include lawn only, not areas covered by sidewalks, driveways or other non-turf. Measure the lawn directly, or measure each non-lawn footprint and let the tool subtract it.

Aerial tools also work. Minnesota walks through a satellite-map ruler: drop pins around the edge and the area totals automatically, in square feet if you change the unit. It works best with recent imagery and a clear view from above, and the program advises rounding up to the nearest 100 square feet, since these tools give rough estimates.

  1. Sketch the lot on paper and mark the house, drive, walks, patio and beds.
  2. Break each lawn area into rectangles, and add a triangle where an edge runs at an angle.
  3. Measure each shape in feet and multiply, then add the shapes. Treat a curved edge as a straight line that splits the difference.
  4. Round up and write the number down, so every crew that quotes gets the same figure.

Linear feet and cubic yards

Fences, edging and gutters are priced by the linear foot: measure the run along the line, not the area it encloses. The fence and deck tool takes the length of the fence line, the width of one section, the number and width of gates and whether the fence closes on itself, and returns sections, posts, rails and pickets. Fence permits and setbacks are local; see fence and deck permits.

Mulch, compost and topsoil are sold by the cubic yard, which is 27 cubic feet. The lawn supplies tool takes the bed area and a depth in inches, and gives cubic yards. One cubic yard spread 3 inches deep covers 108 square feet. For beds, measure the area you will cover, not the length of the edge; see mulching and bed edging.

What the area number leaves out

The lot to lawn tool does not know slope, shade, fences or gates, and a crew may price those. Two lawns with the same square footage can be quoted differently if one is steep or fenced in with a narrow gate. Tell every crew about them when you ask for a quote.

Slope is easy to check. University of Georgia Extension gives the rise over run formula for percent of slope: a drop of 3 feet over a 10-foot run is a 30 percent slope. The same page says riding mowers are unsafe on ground steeper than 27 percent, and that push mowers can be used on slopes up to 20 degrees. For a steep lawn, that is a reason to ask a crew for a quote. See DIY or hire.

Use the number

  • Quotes. Give the same lawn area to every crew and ask what area each quote used. Restate any quote per 1,000 square feet with the yard budget tool to compare quotes. More on that is in budgeting yard work.
  • Fertilizer and seed. Rates on labels are per 1,000 square feet. Minnesota's program notes the same and advises buying extra seed in case you need to reseed. The lawn supplies tool turns a label rate into bags.
  • Sod. The tool adds a percentage for cuts and edges. Ask your supplier how much one pallet covers.

If a crew measures for you, ask what they counted. A written quote that names the area in square feet or the run in linear feet is easier to check than one that says "average lawn."

Questions people ask

How many square feet are in an acre?

One acre is 43,560 square feet. The lot to lawn tool accepts a lot in acres or square feet and converts for you.

How do I find the square footage of my lawn?

Start with the lot size, then subtract the house, driveway, walks and beds. Or break the lawn into rectangles and triangles, measure them with a tape or wheel and add the areas, as Rutgers and the University of Minnesota describe.

What is a linear foot?

One foot of length, whatever the width or height. Fences, edging and gutters are quoted by the linear foot, so measure the run along the line.

Does the lot to lawn tool account for slope or shade?

No. It does not know slope, shade, fences or gates, and a crew may price them. Use it to compare quotes, not as a measurement for a contract.

Sources

Checked on November 20, 2026. The tools give planning figures, not a survey; for a property line or a legal boundary, use a licensed surveyor and your county records.